Worksun Group Co., Ltd. is one of the most reliable manufacturers and suppliers of adjustable column steel formwork in China. If you're going to wholesale bulk classy adjustable column steel formwork, welcome to get pricelist from our factory. All customized products are with high quality and low price.
Introduction
Adjustable column steel formwork is a modular concrete forming system designed for casting square and rectangular columns. Unlike fixed-size column formwork, this system allows you to adjust the column cross-section using the same set of panels – one set of formwork covers multiple column sizes.
The system consists of steel frame panels, adjustable steel walers, column couplers, tie rods, and adjustable support props. Panels are typically fabricated from Q235 or Q355B steel, with 15-18mm film-faced plywood faces. The steel frame depth is usually 120mm or 65mm, depending on the series.
Standard adjustable column formwork covers column cross-sections from 200mm × 200mm up to 1050mm × 1050mm, adjustable in 50mm increments. The same set of panels can be reconfigured for different column sizes on the same project – you do not need new panels for every column dimension.
Advantages
Adjustable sizing. One set of formwork covers a wide range of column sizes. Standard systems handle cross-sections from 200mm × 200mm up to 750mm × 750mm or 1050mm × 1050mm, adjustable in 50mm increments. This reduces the number of different formwork sets you need to keep on site.
High load capacity. Column formwork handles up to 80 kN/m² lateral concrete pressure. This covers most residential, commercial, and industrial column construction – from standard building columns to larger structural elements.
Lightweight handling. Panels weigh approximately 23kg per square metre for aluminium frame systems and 40-65kg per square metre for steel frame systems. Steel frame panels are heavier but cost less – aluminium frame panels are lighter but more expensive.
Good concrete finish. The film-faced plywood face produces smooth, clean concrete surfaces. The surface is typically easy to strip and requires minimal finishing work.
Reusable. With proper care and maintenance, steel frame formwork can be reused 200 cycles or more without damage. The plywood face can be replaced when it wears out – the steel frame stays.
Fast assembly. Panels connect with column couplers and standard – no bolts required. Just a hammer. Two workers can install up to 100 square metres per day.
Features
| Material | Q235 or Q355B steel frame; 15-18mm film-faced plywood face |
| Steel frame depth | 65mm or 120mm (depending on series) |
| Panel thickness | 6mm steel plate (typical) |
| Panel weight | 40-65kg/m² (steel frame) |
| Column size range | 200 × 200mm up to 1050 × 1050mm |
| Adjustment increment | 50mm |
| Load capacity | Up to 80 kN/m² lateral pressure |
| Connection | Column couplers, standard |
| Finish | Powder-coated or painted steel frame |
| Reuse cycles | 200+ with normal care |
Specifications
|
Parameter |
Specification |
|
Material |
Q235 / Q355B steel frame + plywood face |
|
Steel Frame Depth |
65mm or 120mm |
|
Panel Face |
15-18mm film-faced plywood |
|
Panel Weight |
40-65kg/m² |
|
Column Size Range |
200 × 200mm to 1050 × 1050mm |
|
Adjustment Increment |
50mm |
|
Load Capacity |
Up to 80 kN/m² |
|
Connection |
Column couplers / Clamps |
|
Finish |
Powder-coated / Painted |
|
Reuse Cycles |
200+ times |
Custom sizes and configurations available on request.
Application Scope
Adjustable column steel formwork is used wherever square or rectangular concrete columns are required:
- High-rise buildings – structural columns in residential and commercial towers
- Commercial construction – office buildings, shopping malls, hotels
- Industrial facilities – factories, warehouses, and processing plants
- Public infrastructure – stations, airports, stadiums
- Basement and underground structures – below-grade column construction
- Bridge and viaduct projects – pier columns and substructures
The system works particularly well on projects with multiple columns of different sizes – the adjustability of the formwork means you can use the same panels for different column dimensions, reducing the total formwork inventory required on site.
System Components
A complete adjustable column steel formwork system includes:
Panels:
- Standard column panels – various heights and widths
- Corner sections – internal and external
- Adjustment panels – for fine-tuning dimensions
Adjustment System:
- Steel walers – adjustable horizontal members that change the column cross-section
- Column couplers – connect panels and secure the assembly
- Adjustment holes – 50mm increments for precise sizing
Connections:
- Clamps – panel-to-panel connections
- Tie rods and nuts – through-column tensioning
- Flat ties – panel tensioning
Supports:
- Adjustable steel props – vertical support
- Pull-push props – plumb adjustment and stability
- Base jacks – levelling on uneven ground
Accessories:
- PVC sleeves – tie rod extraction
- Working platforms – access during installation
- Lifting hooks – crane handling
Competitive Edge
Adjustable sizing saves money. One set of formwork covers multiple column sizes. You do not need different formwork for 400mm, 500mm, and 600mm columns – the same panels adjust to all three sizes. This reduces both the initial purchase cost and the storage space required on site.
High load capacity. 80 kN/m² lateral pressure rating means you can pour tall columns with fast placement rates without worrying about formwork failure.
Long service life. Steel frames last 200+ cycles with normal care. The plywood face can be replaced when it wears out – the steel frame stays in service.
Good concrete finish. The film-faced plywood face produces smooth, clean concrete surfaces. Often good enough for bare concrete finishes – no plastering needed.
Proven design. Adjustable column steel formwork systems have been used on building projects worldwide for decades. Mature, reliable technology.
Services
Design consultation
free layout planning and panel configuration from your drawings
01
Custom fabrication
non-standard column sizes and special configurations – available on request
02
Technical support
video consultation within 24 hours; on-site for complex projects
03
Delivery
standard panels in 15-20 working days; custom orders 20-30 working days
04
Samples
available for testing – freight to be covered by buyer
05
FAQ
Q: What column sizes can adjustable column steel formwork handle?
A: Standard systems handle column cross-sections from 200mm × 200mm up to 750mm × 750mm or 1050mm × 1050mm, adjustable in 50mm increments. Two series – 750 and 1050 – can be combined to cover rectangular columns up to 1050mm × 750mm.
Q: How does the adjustment work?
A: The steel walers are repositioned to change the column cross-section. The system uses 50mm adjustment holes – you move the walers to the required position and lock them in place. The same set of panels can be reconfigured for different column sizes on the same project.
Q: How much load can adjustable column steel formwork handle?
A: Up to 80 kN/m² lateral concrete pressure. This covers most residential, commercial, and industrial column construction.
Q: How many times can it be reused?
A: Steel frames can be reused 200+ cycles with normal care. The plywood face can be replaced when it wears out – the steel frame stays.
Q: What is the difference between 750 series and 1050 series?
A: 750 series covers columns up to 750mm × 750mm. 1050 series covers columns up to 1050mm × 1050mm. The two series can be combined to cast rectangular columns up to 1050mm × 750mm.
Q: Do I need a crane to handle the panels?
A: Steel frame panels are heavier than aluminium – about 40-65kg per square metre. Larger panels may require a crane. Smaller panels can be handled by two workers.
Q: Can I get custom column sizes?
A: Yes – non-standard column sizes and special configurations are available on request.
Q: How do panels connect?
A: Column couplers and standard – no bolts. Just a hammer. Quick assembly, easy to learn.
Q: How are panels packed for shipping?
A: Flat in steel frames or pallets. A standard container holds about 150-200 square metres of panels.
Q: Can this system be used for walls as well as columns?
A: Yes – the system can also be used for wall construction, offering greater versatility on site.
Hot Tags: adjustable column steel formwork, China adjustable column steel formwork manufacturers, suppliers factory, Adjustable Column Steel Formwork, Cylinder Steel Formwork, Precast Concrete House Of Steel Formwork, Q700 Steel Formwork, steel formwork, Tunnel Formwork

