Worksun Group Co., Ltd. is one of the most reliable manufacturers and suppliers of 120 aluminum frame formwork in China. If you're going to wholesale bulk classy 120 aluminum frame formwork, welcome to get pricelist from our factory. All customized products are with high quality and low price.
Introduction

120 aluminum frame formwork is a modular concrete forming system used for walls, columns, slabs, and beams. The number 120 refers to the total panel thickness – the aluminum frame plus the plywood face – measured in millimetres. This puts it in the heavy-duty category.
The frames are welded from hollow-section aluminum profiles, with 15-18mm film-faced plywood faces attached by rivets. The material is 6061-T6 aluminum alloy – good strength-to-weight ratio, doesn't rust.
120 series is the heavy-duty end of the aluminum frame product line. Stiffer than 65mm or 75mm systems, but still lighter than steel.
Key Benefits
Stiffer than standard aluminum. The 120mm thickness gives you more rigidity than 65mm or 75mm systems. Taller walls, faster concrete placement, less panel deflection.
Heavy-duty capacity, still light. About 23kg per square metre. The biggest panel – 3000mm × 1000mm – weighs roughly 63-71kg. Two workers can handle it. No crane needed for normal handling.
High load capacity. Wall formwork handles 60 kN/m². Columns take up to 80 kN/m². Enough for high-rise and heavy pours.
Doesn't rust. Aluminum does not corrode. 6061-T6 alloy with powder coating holds up in wet conditions, coastal sites, and chemical environments where steel would degrade.
Long service life. With normal care, 100 uses or more. Replace the plywood face when it wears out – the aluminum frame stays.
Clean concrete finish. The flat plywood face produces smooth concrete surfaces. Often good enough for bare concrete – no plastering.
Recyclable. 100% recyclable at end of life. Good scrap value.

Technical Data
| Panel thickness | 120mm (aluminum frame + plywood face) |
| Frame material | 6061-T6 aluminum alloy |
| Frame section | Hollow aluminum profiles |
| Panel face | 15-18mm film-faced plywood |
| Panel weight | approximately 23kg/m² |
| Maximum panel size | 3000mm × 1000mm (approx. 63-71kg) |
| Wall load capacity | 60 kN/m² |
| Column load capacity | 80 kN/m² |
| Reuse cycles | 100+ times with normal care |
| Connection | Clamps or pins and wedges |
| Finish | Powder-coated or anodized |
| Recyclability | 100% |
Specifications
|
Parameter |
Specification |
|
Panel Thickness |
120mm |
|
Frame Material |
6061-T6 aluminum alloy |
|
Frame Section |
Hollow aluminum profiles |
|
Panel Face |
15-18mm film-faced plywood |
|
Panel Weight |
~23kg/m² |
|
Max Panel Size |
3000mm × 1000mm |
|
Wall Load Capacity |
60 kN/m² |
|
Column Load Capacity |
80 kN/m² |
|
Reuse Cycles |
100+ times |
|
Connection |
Clamps / Pins and wedges |
|
Finish |
Powder-coated / Anodized |
|
Recyclability |
100% |
Application Scope

120 aluminum frame formwork handles heavy concrete work:
► Walls – high-rise residential, commercial, industrial shear walls
► Columns – large square and rectangular sections
► Slabs – floor and roof
► Beams – various depths and widths
► Bridge piers and abutments
► Tunnels and underground structures
► Power plants and industrial facilities
► Large civil infrastructure
Use this when standard aluminum systems (65mm or 75mm) are not stiff enough, but you still want the weight advantage of aluminum over steel. It gives you steel-like stiffness at roughly one-third the weight.
System Components
A complete 120 aluminum frame formwork system includes:
Panels:
► Standard wall panels – various widths and heights
► Column panels – adjustable for different sizes
► Corner sections – internal and external
► Filler panels – for infill and adjustment
Connections:
► Clamps – panel-to-panel connections
► Pins and wedges – alternative
► Flat ties – panel tensioning


Reinforcement:
► Tie rods and nuts – through-wall tensioning
► Walers – horizontal bracing
► Corner braces – stability at corners
Supports:
► Adjustable steel props – vertical support
► Base jacks – levelling
► Pull-push props – plumb adjustment
Competitive Edge
Stiffness without the weight. 120mm thickness gives you rigidity comparable to heavy steel formwork, at about one-third the weight. Easier to handle, less crane time, lower labour costs.
High capacity. 60-80 kN/m² covers most residential, commercial, and industrial concrete work.
Corrosion-resistant. Aluminum does not rust. Works in wet conditions, coastal areas, and environments where steel would corrode.
Long-term value. 100+ reuse cycles means the per-use cost is low. Replace only the plywood face when it wears out – the aluminum frame stays.
Good concrete finish. Smooth, flat panel face produces high-quality concrete surfaces – often bare concrete quality, no plastering needed.
Sustainable. Aluminum is 100% recyclable with good scrap value.
Proven design. Similar systems have been used on large projects worldwide for decades.
Services
Design consultation
free layout planning and panel configuration from your drawings
01
Custom fabrication
non-standard sizes and special configurations available on request
02
Technical support
video consultation within 24 hours; on-site for complex projects
03
Delivery
standard panels in 15-20 working days; custom orders 20-30 working days
04
Samples
available for testing – freight to be covered by buyer
05
FAQ
Q: What does 120 mean?
A: Total panel thickness – 120mm, including the aluminum frame and plywood face. Heavy-duty option in the aluminum frame range.
Q: How much load can it handle?
A: Wall formwork takes 60 kN/m². Column formwork takes up to 80 kN/m².
Q: Is it heavier than standard aluminum systems?
A: Slightly – about 23kg/m² compared to 18-20kg/m² for 65mm systems. Extra weight gives you more stiffness and capacity.
Q: What projects is it best for?
A: Projects where standard aluminum isn't stiff enough, but you still want aluminum's weight advantage over steel – high-rise buildings, large columns, heavy structural elements.
Q: How many times can it be reused?
A: 100+ times with normal care. The aluminum frame lasts longer – replace the plywood face when it wears out.
Q: How does it compare to steel frame formwork?
A: Aluminum is lighter (23kg/m² vs 50-65kg/m² for steel), doesn't rust, and is easier to handle. Steel is cheaper upfront but heavier and prone to rust. Aluminum gives better long-term value on projects with many reuses.
Q: What panel sizes are available?
A: Standard panels up to 3000mm × 1000mm. Custom sizes on request.
Q: How do panels connect?
A: Clamps or pins and wedges – both available.
Q: Can I get custom panel sizes?
A: Yes – non-standard sizes and special configurations available.
Q: What concrete finish quality can I expect?
A: Smooth, high-quality surface – often good for bare concrete finishes. No plastering needed in most cases.
Q: Does aluminum frame formwork corrode?
A: No. Aluminum does not rust. 6061-T6 with powder coating withstands moisture, coastal conditions, and chemical exposure.
Q: Do I need special tools for assembly?
A: No. Standard clamps or pins and wedges – just a hammer.
Q: How are panels packed for shipping?
A: Flat in steel frames or pallets. A standard container holds about 150-200 square metres of panels.
Q: Can the plywood face be replaced on site?
A: Yes. Remove the old plywood, clean the frame, attach the new face with screws or rivets. Pre-cut replacement faces also available.
Hot Tags: 120 aluminum frame formwork, China 120 aluminum frame formwork manufacturers, suppliers factory, 100 Aluminum Frame Formwork, 117 Aluminum Frame Formwork, 120 Aluminum Frame Formwork, 150 Alu SkyDeck Formwork, aluminum frame formwok

