Cylinder Steel Formwork

Cylinder Steel Formwork
Product Introduction:
Cylinder steel formwork is used for casting circular columns, bridge piers, and other round concrete structures. Unlike flat formwork, this system must hold a round shape under concrete pressure and keep the same diameter from bottom to top.
Send Inquiry
Description
Technical Parameters

Worksun Group Co., Ltd. is one of the most reliable manufacturers and suppliers of cylinder steel formwork in China. If you're going to wholesale bulk classy cylinder steel formwork, welcome to get pricelist from our factory. All customized products are with high quality and low price.

 

Introduction

 

1001

Cylinder steel formwork is used for casting circular columns, bridge piers, and other round concrete structures. Unlike flat formwork, this system must hold a round shape under concrete pressure and keep the same diameter from bottom to top.

The panels are curved steel - normally two halves or multiple sections - bolted together to form a full circle. Material is Q235B steel, with plate thickness from 4mm up to 6mm or more, depending on diameter and pressure needs. Standard diameters run 0.4m to 2m, with section heights of 1m, 1.5m, 2m, and 3m.

This system is built for repeated use. With ordinary site care, cylinder steel formwork delivers many reuses, which makes it a solid choice for projects with multiple circular columns or repetitive pier pours.

 

Advantages

 

Keeps its shape. Curved panels are precision-formed to stay round under concrete pressure. Two-half or segmented design keeps the diameter consistent pour after pour.

Good surface finish. The smooth steel face gives clean, quality concrete. Vertical deviation stays under 3mm, and the finished surface needs very little touch-up.

Tough. Q235B steel handles impact and wear well. With normal site care, the panels keep going through many projects.

Fast setup. Prefabricated panels cut on-site prep time. Panels bolt together quickly - two or three workers can handle a typical section. Only one vertical seam to close, so alignment is simple.

Adjustable sizing. The segmented design lets you adjust diameter within a range, so you can use the same formwork for different column sizes on one job.

Rust protection. Panels can be coated with anti-corrosion finish for coastal work, wet conditions, or outdoor storage.

7001

 

Features

Material Q235B carbon steel (Q345B for higher loads)
Plate thickness 4mm – 6mm (depends on diameter and pressure)
Diameter range 0.4m – 2.0m standard (custom up to 2.5m+)
Section heights 1m, 1.5m, 2m, 3m (stackable)
Panel configuration two halves (standard) or multiple segments (large diameters)
Connection bolted flanges
Lateral pressure rating up to 85 kN/m²
Verticality tolerance ≤ 3mm
Surface flatness ≤ 1.5mm
Finish anti-corrosion coating or bare steel

 

Specifications

 

Parameter

Specification

Material

Q235B / Q345B steel

Plate Thickness

4mm – 6mm (custom available)

Diameter Range

0.4m – 2.0m (custom up to 2.5m+)

Section Heights

1m, 1.5m, 2m, 3m (stackable)

Panel Segments

2 halves (standard) / multiple (large diameters)

Connection

Bolted flanges

Lateral Pressure

Up to 85 kN/m²

Verticality Tolerance

≤ 3mm

Surface Flatness

≤ 1.5mm

Finish

Anti-corrosion coating / Bare steel

Custom diameters, heights, and thicknesses available on request.

 

Application Scope

 

1

Cylinder steel formwork is used wherever you need circular concrete columns or piers:

► Bridge work – circular piers, pier columns, and abutments

► High-rise buildings – circular structural columns in commercial and residential towers

► Public infrastructure – airport columns, station pillars, stadium supports

► Industrial sites – circular columns in factories and warehouses

► Architectural features – decorative circular columns in lobbies, atriums, and public spaces

► Utility structures – circular manholes, inspection shafts, and well casings

► Wind power – circular base structures

► Municipal projects – circular columns in water treatment and utility work

The system pays off best on jobs with multiple circular columns of the same diameter, where reusing the formwork spreads the cost. Larger diameters (2m and above) usually need thicker steel plate (6mm or more) to prevent deformation under concrete pressure.

 

System Components

 

A complete cylinder steel formwork system includes:

Panels:

► Curved steel panels – two halves or multiple segments

► Flanged edges – for bolted connections between segments

► Stiffeners – built-in ribs that prevent deformation under load

Connections:

► Bolts and nuts – hold panel segments together

► Flange plates – vertical and horizontal connection points

► Alignment pins – help keep things lined up during assembly

10001
13001

Reinforcement:

► Steel hoops or straps – circumferential bracing for larger diameters

► External bracing – extra stability during pouring

Supports:

► Adjustable steel props – vertical support during erection

► Pull-push props – plumb adjustment and stability

► Base jacks – levelling on uneven ground

 

Accessories:

► Lifting hooks – for crane handling

► PVC sleeves – for tie rod extraction (when used)

► Working platforms – access during installation

 

Competitive Edge

 

1

Accurate. Curved panels are formed to keep a true circular shape. Verticality holds within 3mm - straight, round columns every time.

2

Durable. Q235B steel resists impact and wear. With proper care, the system stays in service across many projects.

3

Quick to set up. Prefabricated panels reduce on-site prep time. Two or three workers can assemble typical sections quickly. Only one vertical seam to close - simple and efficient.

4

Clean finish. The steel face gives clean, quality concrete that needs very little finishing.

5

Flexible. Standard diameters from 0.4m to 2m, stackable heights up to 3m or more. Custom sizes available for larger or non-standard columns.

6

Cost-effective. High reuse cycles mean the per-use cost is lower than timber or single-use systems over the long run.

7

Proven. Cylinder steel formwork has been used on bridge, building, and infrastructure projects for decades. Mature, reliable.

 

Services

 

Design consultation

free layout planning and panel configuration from your drawings

01

Custom fabrication

non-standard diameters, heights, and thicknesses – available on request

02

Technical support

video consultation within 24 hours; on-site for complex projects

03

Delivery

standard panels in 15-20 working days; custom orders 20-30 working days

04

Samples

available for testing – freight to be covered by buyer

05

 

FAQ

 

Q: What diameters can this system handle?

A: Standard diameters range from 0.4m to 2.0m. Custom diameters up to 2.5m or larger are available on request.

Q: How thick should the steel plate be?

A: Minimum is 4mm. For larger diameters (2m and above), 6mm or thicker is recommended to prevent deformation under concrete pressure.

Q: How do you assemble the formwork?

A: Curved panels – usually two halves – bolt together at the flanged edges to form a complete circle. Sections can be stacked vertically to reach the height you need.

Q: How many reuses can I expect?

A: With proper care and maintenance, steel formwork lasts across many projects. Actual number depends on site conditions and handling, but steel significantly outlasts timber.

Q: What concrete finish quality will I get?

A: The smooth steel surface gives clean, high-quality concrete with verticality within 3mm. Very little finishing is typically required.

Q: Can I get custom sizes?

A: Yes – custom diameters, heights, and plate thicknesses are available on request.

Q: How are panels packed for shipping?

A: Flat in steel frames or pallets. Curved segments nest together to save space.

Q: Can this be used for tapered columns?

A: Standard cylinder formwork is for straight circular columns. Tapered or conical columns require custom-fabricated panels.

 

Hot Tags: cylinder steel formwork, China cylinder steel formwork manufacturers, suppliers factory, Adjustable Column Steel Formwork, Cylinder Steel Formwork, Precast Concrete House Of Steel Formwork, Q700 Steel Formwork, steel formwork, Tunnel Formwork

Send Inquiry