Worksun Group Co., Ltd. is one of the most reliable manufacturers and suppliers of pp hollow plastic formwork in China. If you're going to wholesale bulk classy pp hollow plastic formwork, welcome to get pricelist from our factory. All customized products are with high quality and low price.
Introduction
PP hollow plastic formwork is made from polypropylene resin through blow-moulding or extrusion. The hollow-core design with internal ribbing cuts weight while keeping strength where it matters.
Standard panel sizes are 1,220mm × 2,440mm or 915mm × 1,830mm, with thicknesses from 12mm to 22mm. A 15mm panel weighs about 24-25kg; an 18mm panel weighs about 28-29kg. That works out to roughly 8-10kg per square metre – one of the lightest formwork options out there.
With normal site handling, panels give you 50-80 uses, sometimes up to 100 if you look after them. Field data shows cost savings of up to 40% compared to conventional timber formwork.
Advantages
Light and labour-saving. The hollow core keeps weight at 8-10kg/m² – a lot lighter than plywood or steel. One worker can handle most panel sizes. This speeds up installation, cuts labour costs, and lowers freight bills.
High reuse. You get 50-80 uses typically, sometimes up to 100. Plywood gives you 3-5. The per-use cost drops sharply over the project, so it ends up cheaper than timber in the long run.
Waterproof. Polypropylene does not soak up water. Panels are 100% waterproof – no swelling, no warping, no rotting. They work well in basements, underground, and damp sites where timber rots and steel rusts.
No release oil needed. The smooth, non-porous surface does not hold concrete. After stripping, just rinse with water – no oil, no chemicals, no extra cost.
Clean concrete finish. The panel surface gives a smooth, glossy finish. It often meets bare concrete standards, so you can skip plastering.
Chemical resistant. PP handles diluted acids, alkalis, and corrosion. Good for coastal work, chemical plants, mine sites, and seawalls.
Easy to modify on site. Cut, saw, drill, and nail with ordinary woodworking tools. Works with timber, steel, and aluminium framing. No special gear needed.
Temperature range. PP melts at 167°C and softens at 150°C. Panels work from -20°C to +90°C – fine for both hot climates and freezing conditions.
Recyclable. Made from polypropylene. Fully recyclable at end of life. Waste material can be reprocessed.

Features
| Material | Polypropylene (PP) – typically 80% PP with additives |
| Construction | Hollow-core with internal ribs |
| Standard sizes | 1,220mm × 2,440mm; 915mm × 1,830mm |
| Thickness options | 12, 13, 14, 15, 18, 20, 22mm |
| Colour options | Black, white |
| Surface | Smooth, non-porous, non-stick |
| Water absorption | None |
| Chemical resistance | Acid and alkali resistant |
| Workability | Standard woodworking tools – cut, saw, drill, nail, screw |
| Recyclability | 100% |
Specifications
PP Hollow Plastic Formwork Common Sizes
|
Parameter |
Common Specification |
|
Common Length |
1830 / 2440 mm |
|
Common Width |
915 / 1220 mm |
|
Common Panel Size |
915 × 1830 mm |
|
Common Panel Size |
1220 × 2440 mm |
|
Common Thickness |
12 / 15 / 18 / 20 mm |
|
Commonly Sold Thickness |
15 / 18 mm |
|
Other Thicknesses |
14 / 16 / 17 mm |
Application Scope

PP hollow plastic formwork handles most cast-in-place concrete jobs:
► Wall formwork – residential, commercial, industrial shear walls
► Slab and deck formwork – floors, roofs, bridge decks
► Column formwork – square and rectangular columns
► Beam formwork – various depths and widths
► Basement and underground – waterproof and corrosion-resistant
► Infrastructure – tunnels, canals, bridges
► Coastal and marine – seawalls, pier works
► Residential and commercial buildings – apartments, villas, offices
The system works best on projects where you get multiple uses out of the panels. Its light weight and easy modification also make it practical for sites with limited crane access or where on-site changes are common.
System Components
Panels:
► Standard hollow panels – various thicknesses and sizes
► Corner sections – internal and external
► Custom-cut panels – supplied to specification
Connection hardware:
► Connecting pins and wedges – for panel-to-panel joints
► Clamps and brackets – for securing panels to supports
► Nails and screws – standard fasteners work
Reinforcement:
► Steel or aluminium walers – horizontal bracing for large walls
► Timber or steel beams – secondary support members
Support equipment:
► Adjustable steel props – vertical support
► Base jacks – levelling on uneven ground
► Pull-push props – plumb adjustment and stabilisation
Additional components available for custom configurations.
Competitive Advantages
Cost. PP hollow formwork is priced competitively against plywood. With 50-80 reuse cycles, the per-use cost is much lower. Field data shows savings up to 40% compared to conventional timber formwork.
Weight. At 8-10kg per square metre, it is significantly lighter than plywood and steel. This cuts labour costs, speeds up installation, and reduces transport expenses.
Concrete finish. The smooth panel surface delivers a clean, glossy finish – often achieving bare concrete quality and eliminating plastering.
Durability. Waterproof, corrosion-resistant, chemically stable. No swelling, warping, or rotting. Service life is much longer than timber under normal site conditions.
Environmental. Made from polypropylene. 100% recyclable at end of life. Supports green building certification and reduces construction waste.
Site flexibility. Cut and drill with ordinary woodworking tools – no special equipment needed.
Export documentation. Full export documentation provided – material test reports, inspection certificates, customs clearance – for smooth international delivery.
Services
Design consultation
free layout planning and panel configuration from your drawings
01
Custom fabrication
non-standard sizes, thicknesses, and configurations available on request
02
Technical support
video consultation within 24 hours; on-site support for complex projects
03
Delivery
standard panels in 5-10 working days; custom orders in 15-20 working days
04
Samples
available for testing – freight to be covered by buyer
05
FAQ
Q: How many uses can I get from PP hollow plastic formwork?
A: 50-80 uses with normal site handling. Some formulations reach 80-100 cycles with careful use. This is what makes it more economical than plywood over a full project.
Q: Do I need release agent?
A: No. The smooth, non-porous surface prevents concrete from sticking. Water cleaning after stripping is sufficient. No oil, no chemicals.
Q: Can I cut and drill these panels on site?
A: Yes. Standard woodworking tools work – saws, drills, nail guns. Compatible with timber, steel, and aluminium framing.
Q: What temperature range can they handle?
A: -20°C to +90°C. The material melts at 167°C and softens at 150°C – well above normal construction conditions.
Q: Are they waterproof?
A: Yes. 100% waterproof. No swelling, no rotting. Suitable for underground, basement, and damp-site work.
Q: Are they resistant to chemicals?
A: Yes. PP resists diluted acids, alkalis, and corrosion. Suitable for coastal areas, chemical plants, and mine sites.
Q: What concrete finish quality can I expect?
A: Smooth, clean finish. Achieves bare concrete quality – often eliminates the need for plastering.
Q: How heavy are the panels?
A: Approximately 8-10kg per square metre. A 15mm panel weighs about 24-25kg; an 18mm panel weighs about 28-29kg. One person can handle most sizes.
Q: Are they recyclable?
A: Yes. 100% recyclable at end of life. Waste material can be reprocessed.
Q: Can I order samples?
A: Yes – samples available for testing. Freight to be covered by buyer. Each sample marked with panel specifications.
Hot Tags: pp hollow plastic formwork, China pp hollow plastic formwork manufacturers, suppliers factory, 65 PP Plastic Formwork, 75 ABS Plastic Formwork, 78 ABS Plastic Formwork, 78 PP Plastic Formwork, plastic formwork, PP Hollow Plastic Formwork
