100 Aluminum Frame Formwork

100 Aluminum Frame Formwork
Product Introduction:
100 aluminum frame formwork is a modular forming system for walls, columns, slabs, and beams. The "100" refers to the frame thickness – 100mm. In aluminum frame formwork, this is the standard specification.
Send Inquiry
Description
Technical Parameters

Worksun Group Co., Ltd. is one of the most reliable manufacturers and suppliers of 100 aluminum frame formwork in China. If you're going to wholesale bulk classy 100 aluminum frame formwork, welcome to get pricelist from our factory. All customized products are with high quality and low price.

 

Introduction

 

100 Aluminum Frame Formwork 2001

100 aluminum frame formwork is a modular forming system for walls, columns, slabs, and beams. The "100" refers to the frame thickness – 100mm. In aluminum frame formwork, this is the standard specification.

Frames are welded from hollow extruded aluminum sections, with plywood faces riveted on. The alloy is 6061-T6. Plywood thickness is 12mm, 15mm, or 18mm – depends on the application.

100 series is standard-duty. Lighter than 120mm or 140mm heavy systems, but still handles 60 kN/m². Sits between the lightweight 65mm systems and the heavy-duty options.

 

Key Features

 

60 kN/m² capacity. Handles most residential, commercial, and light industrial wall and column work. The 100mm frame takes typical concrete pressure without excessive deflection.

Weight. Panels run about 23kg per square metre. The biggest standard panel – 900mm × 3000mm – is roughly 62kg. Two workers can manage it. No crane needed for normal handling.

Corrosion resistance. 6061-T6 aluminum does not corrode. Frames come powder-coated or bare. Works fine in wet conditions, coastal sites – anywhere steel would rust.

Service life. 100+ reuses with normal site care. Replace the plywood face when it wears out – the aluminum frame stays in service.

Concrete finish. The plywood face gives smooth, even concrete surfaces. Verticality typically within 4mm. Often good enough for bare concrete – no plastering.

Standardization. Standard widths: 900, 600, 450, 300mm. Heights: 600 to 3300mm. Fewer panel types means simpler logistics and faster setup.

Assembly speed. Panel clamps – no bolts. Just a hammer. Fixed and hinged corners handle different wall layouts.

Recyclability. 100% recyclable at end of life.

100 Aluminum Frame Formwork 3001

 

Technical Data

Frame profile 100mm
Frame material 6061-T6 aluminum alloy
Panel face 12-18mm film-faced birch plywood
Panel weight approximately 23kg/m²
Standard heights 600, 900, 1200, 2400, 2700, 3000, 3300mm
Standard widths 300, 450, 600, 900mm
Max panel 900 × 3000mm
Load capacity 60 kN/m²
Connection Panel clamps
Finish Powder-coated or bare aluminum
Reuse cycles 100+ with normal care

 

Specifications

 

Parameter

Specification

Frame Profile

100mm

Frame Material

6061-T6 Aluminum Alloy

Panel Face

12-18mm Birch Plywood

Panel Weight

~23kg/m²

Standard Heights

600 / 900 / 1200 / 2400 / 2700 / 3000 / 3300mm

Standard Widths

300 / 450 / 600 / 900mm

Max Panel Size

900 × 3000mm

Load Capacity

60 kN/m²

Connection

Clamps

Finish

Powder-coated / Bare

Reuse Cycles

100+ times

 

Application Scope

 

100 Aluminum Frame Formwork 6001

100 aluminum frame formwork fits most concrete work:

► Walls – residential, commercial, light industrial shear walls

► Columns – square and rectangular sections

► Slabs – floor and roof

► Beams – various depths and widths

► Foundations and footings

► Swimming pools and water tanks

► Housing, commercial buildings, civil projects

Best where 60 kN/m² is sufficient – which covers most residential and commercial construction.

 

System Components

A complete system includes:

Panels:

► Standard wall panels – various heights and widths

► Column panels – adjustable

► Corner sections – fixed and hinged

► Filler panels – for adjustment

Connections:

► Panel clamps – quick panel-to-panel connections

► Tie rods and nuts – through-wall tensioning

► Flat ties – panel tensioning

100 Aluminum Frame Formwork 10
100 Aluminum Frame Formwork 9

Reinforcement:

► Walers – horizontal bracing

► Corner braces – stability at corners

Supports:

► Adjustable steel props – vertical support

► Pull-push props – plumb adjustment

► Base jacks – levelling

 

Accessories:

► PVC sleeves – tie rod extraction

► Working platforms – access during installation

► Lifting hooks – crane handling

 

Competitive Edge

 

1

Standard capacity, light weight. 60 kN/m² handles most work. 23kg/m² means easy handling – no crane required for normal operations.

2

Fewer parts. Standardized widths and heights mean fewer panel types on site. Simpler logistics, faster assembly.

3

Corrosion-free. Aluminum does not rust. Works in wet conditions and coastal areas where steel would corrode.

4

Low per-use cost. 100+ reuse cycles. Replace only the plywood face when it wears out.

5

Good surface quality. Smooth, even concrete surfaces. Often meets bare concrete standards – no plastering needed.

6

Versatile. Works for walls, columns, slabs, and beams. Fixed and hinged corners handle different wall geometries.

7

Proven. Similar systems have been used worldwide for decades. Mature, reliable technology.

 

Services

 

Design consultation

free layout planning from your drawings

01

Custom fabrication

non-standard sizes and special configurations available

02

Technical support

video consultation within 24 hours; on-site for complex projects

03

Delivery

standard panels in 15-20 working days; custom orders 20-30 working days

04

Samples

available for testing – freight to be covered by buyer

05

 

FAQ

 

Q: What does the 100 mean?

A: The frame thickness – 100mm. This is the standard specification in aluminum frame formwork, with 60 kN/m² load capacity.

Q: How much load can it take?

A: 60 kN/m² lateral pressure. Enough for most residential and commercial concrete work.

Q: How heavy is a panel?

A: About 23kg per square metre. The largest standard panel – 900mm × 3000mm – is about 62kg. Two workers can handle it.

Q: What sizes are available?

A: Standard heights: 600, 900, 1200, 2400, 2700, 3000, 3300mm. Standard widths: 300, 450, 600, 900mm. Custom sizes on request.

Q: How many times can I reuse it?

A: 100+ cycles with normal care. The aluminum frame lasts longer – replace the plywood face when it wears out.

Q: What finish does the concrete get?

A: Smooth, even surfaces. Verticality within 4mm – often good enough for bare concrete, no plastering.

Q: Does it rust?

A: No. 6061-T6 aluminum does not rust. Suitable for wet conditions and coastal sites.

Q: Do I need a crane?

A: No. Panels are light enough for manual handling – two workers can handle the largest panel.

Q: How do panels connect?

A: Panel clamps – no bolts. Just a hammer. Quick assembly, easy to learn.

Q: Can I get custom sizes?

A: Yes – non-standard sizes and special configurations available on request.

Q: How does 100mm compare to 120mm or 140mm?

A: 100mm is the standard option – 60 kN/m², lighter weight. 120mm and 140mm are heavy-duty – higher capacity, heavier panels. Choose 100 for most residential and commercial work. Choose 120/140 for tall pours, high pressure, or large structural elements.

Q: How are panels packed for shipping?

A: Flat in steel frames or pallets. A standard container holds about 150-200 square metres of panels.

Q: Can the plywood face be replaced on site?

A: Yes. Remove the old plywood, clean the frame, attach the new face with screws or rivets. Pre-cut replacement faces also available.

 

Hot Tags: 100 aluminum frame formwork, China 100 aluminum frame formwork manufacturers, suppliers factory, 100 Aluminum Frame Formwork, 117 Aluminum Frame Formwork, 120 Aluminum Frame Formwork, 150 Alu SkyDeck Formwork, aluminum frame formwok

Send Inquiry