117 Aluminum Frame Formwork

117 Aluminum Frame Formwork
Product Introduction:
117 aluminum frame formwork is a modular forming system for walls and columns. The “117” refers to the panel depth in millimetres – 117mm. This sits between the standard 100mm systems and the heavier 120/140mm systems in the aluminum frame product line.
Send Inquiry
Description
Technical Parameters

Worksun Group Co., Ltd. is one of the most reliable manufacturers and suppliers of 117 aluminum frame formwork in China. If you're going to wholesale bulk classy 117 aluminum frame formwork, welcome to get pricelist from our factory. All customized products are with high quality and low price.

 

Introduction

 

117 Aluminum Frame Formwork 1002

117 aluminum frame formwork is a modular forming system for walls and columns. The "117" refers to the panel depth in millimetres – 117mm. This sits between the standard 100mm systems and the heavier 120/140mm systems in the aluminum frame product line.

The frames are welded from hollow extruded aluminum profiles with plywood faces riveted on. The alloy is 6061-T6. Standard plywood thickness is 15mm or 18mm. Panel depth is 117mm. The system is rated for 60 kN/m² lateral concrete pressure.

117 series is a middle-ground option – stiffer than 100mm standard systems, lighter than 120mm or 140mm heavy-duty systems. It suits jobs that need more rigidity than 100mm provides but don't call for the full capacity of the heavy options.

 

Advantages

 

60 kN/m² load capacity. The 117mm depth delivers 60 kN/m² lateral pressure capacity. That covers most residential, commercial, and light industrial wall and column forming work.

Lighter than 120mm systems. Stiffer than 100mm, but lighter than 120mm heavy systems. Panels run about 23kg per square metre. The largest standard panel – 3000mm × 1000mm – weighs roughly 70.9kg. Two workers can handle it. No crane needed for normal handling.

Corrosion-resistant. 6061-T6 aluminum does not corrode. Frames are powder-coated for extra protection. Works in wet conditions, coastal sites, and anywhere steel formwork would rust.

Durable. With normal site care, you get 100+ reuse cycles. Replace the plywood face when it wears out – the aluminum frame stays in service.

Good concrete finish. The plywood face gives you smooth, even concrete surfaces. Often good enough for bare concrete finishes – no plastering required.

Quick assembly. Panels connect with universal adjustable alignment clamps. No bolts – just a hammer. Fast setup, easy to learn.

Recyclable. 100% recyclable at end of life.

117 Aluminum Frame Formwork 2001

 

Technical Data

Panel depth 117mm
Frame material 6061-T6 aluminum alloy
Panel face 15-18mm plywood
Panel weight approximately 23kg/m²
Standard panel heights 3000mm, 2500mm, 1250mm
Standard panel widths 1000mm, 750mm, 500mm, 250mm
Largest panel 3000mm × 1000mm, approx. 70.9kg
Load capacity 60 kN/m²
Frame finish Powder-coated
Reuse cycles 100+ with normal care

 

Specifications

 

Parameter

Specification

Panel Depth

117mm

Frame Material

6061-T6 Aluminum Alloy

Panel Face

15-18mm Plywood

Panel Weight

~23kg/m²

Standard Heights

3000 / 2500 / 1250mm

Standard Widths

1000 / 750 / 500 / 250mm

Max Panel Size

3000 × 1000mm (~70.9kg)

Load Capacity

60 kN/m²

Frame Finish

Powder-coated

Connection

Alignment clamps

Reuse Cycles

100+ times

 

Application Scope

 

117 Aluminum Frame Formwork 3002

117 aluminum frame formwork fits most concrete work:

► Walls – residential, commercial, light industrial shear walls

► Columns – square and rectangular columns

► Commercial structures – office towers, retail podiums

► Substructures and basements – underground forming

► High-rise residential – repetitive multi-family housing

► Foundations and retaining walls

Best where 100mm is not stiff enough but 120mm or 140mm heavy systems are more than needed. A balanced middle option.

 

System Components

A complete 117 aluminum frame formwork system includes:

Panels:

► Standard wall panels – various heights and widths

► Column panels – adjustable

► Corner sections – internal and external

► Filler panels – for adjustment

Connections:

► Universal alignment clamps – quick panel-to-panel connections

► Tie rods and nuts – through-wall tensioning

► Flat ties – panel tensioning

117 Aluminum Frame Formwork 4001
117 Aluminum Frame Formwork 4002

Reinforcement:

► Walers – horizontal bracing

► Corner braces – stability at corners

Supports:

► Adjustable steel props – vertical support

► Pull-push props – plumb adjustment

► Base jacks – levelling

 

Accessories:

► PVC sleeves – tie rod extraction

► Working platforms – access during installation

► Lifting hooks – crane handling

 

Competitive Edge

 

1

Balanced stiffness. 117mm gives you more rigidity than 100mm systems. Handles 60 kN/m² – enough for most residential and commercial work.

2

Lighter than heavy systems. At 23kg/m², it is lighter than 120mm or 140mm heavy-duty options. Easier handling, less crane time.

3

No corrosion worries. Aluminum does not rust. Powder-coated finish adds extra protection. Works in wet conditions and coastal areas.

4

Low per-use cost. 100+ reuse cycles. Replace only the plywood face when it wears out.

5

Good surface quality. Smooth, even concrete – often good enough for bare concrete, no plastering.

6

Quick assembly. Universal adjustable clamps – no bolts. Just a hammer.

7

Proven design. Similar systems have been used worldwide for decades. Mature, reliable.

 

Services

 

Design consultation

free layout planning from your drawings

01

Custom fabrication

non-standard sizes and special configurations available

02

Technical support

video consultation within 24 hours; on-site for complex projects

03

Delivery

standard panels in 15-20 working days; custom orders 20-30 working days

04

Samples

available for testing – freight to be covered by buyer

05

 

FAQ

 

Q: What does 117 mean?

A: The panel depth – 117mm. It sits between 100mm standard systems and 120/140mm heavy-duty systems in the aluminum frame range.

Q: How much load can it handle?

A: 60 kN/m² lateral pressure. Enough for most residential and commercial concrete work.

Q: How heavy is a panel?

A: About 23kg per square metre. The largest panel – 3000mm × 1000mm – is about 70.9kg. Two workers can handle it.

Q: What sizes are available?

A: Standard heights: 3000, 2500, 1250mm. Standard widths: 1000, 750, 500, 250mm. Custom sizes on request.

Q: How many times can I reuse it?

A: 100+ cycles with normal care. The aluminum frame lasts longer – replace the plywood face when it wears out.

Q: What finish does the concrete get?

A: Smooth, even surfaces. Often good enough for bare concrete – no plastering.

Q: Does it rust?

A: No. 6061-T6 aluminum does not rust. Powder-coated finish adds extra protection.

Q: Do I need a crane?

A: No. Panels are light enough for manual handling – two workers can handle the largest panel.

Q: How do panels connect?

A: Universal adjustable alignment clamps – no bolts. Just a hammer. Quick assembly, easy to learn.

Q: Can I get custom sizes?

A: Yes – non-standard sizes and special configurations available.

Q: How does 117mm compare to 100mm and 120mm?

A: 117mm is the middle option – more stiffness than 100mm, lighter than 120mm. A balanced choice for projects needing extra stiffness without the weight of heavy-duty systems.

Q: How are panels packed for shipping?

A: Flat in steel frames or pallets. A standard container holds about 150-200 square metres of panels.

Q: Can the plywood face be replaced on site?

A: Yes. Remove the old plywood, clean the frame, attach the new face with screws or rivets. Pre-cut replacement faces also available.

 

Hot Tags: 117 aluminum frame formwork, China 117 aluminum frame formwork manufacturers, suppliers factory, 100 Aluminum Frame Formwork, 117 Aluminum Frame Formwork, 120 Aluminum Frame Formwork, 150 Alu SkyDeck Formwork, aluminum frame formwok

Send Inquiry